![]() ![]() Refer to the following message from Ubuntu's mailing list if you want to learn more. Warning: The driver descriptor says the physical block size is 2048 bytes, but Linux says it is 512 bytes.Īll these warnings are safe to ignore, and your drive should be able to boot without any problems. Try making a fresh table, and using Parted's rescue feature to recover partitions. Is this a GPT partition table? Both the primary and backup GPT tables are corrupt. Or perhaps you deleted the GPT table, and are now using an msdos partition table. Perhaps it was corrupted - possibly by a program that doesn't understand GPT partition tables. However, it does not have a valid fake msdos partition table, as it should. dev/xxx contains GPT signatures, indicating that it has a GPT table. Good luck! Here is the link.Ubuntu images (and potentially some other related GNU/Linux distributions) have a peculiar format that allows the image to boot without any further modification from both CDs and USB drives.Ī consequence of this enhancement is that some programs, like parted get confused about the drive's format and partition table, printing warnings such as: I really like it because I don't have to run an ugly cable down the wall to get power.Īgain just make sure you can access BOTH your USB & HDMI ports on the back of your TV or get some help getting to them. We use both tv's/ sticks with Netflix and a few other services as a daily driver and I haven't had a single problem with my sticks or the cable over the past few months. I have one stick with a cable in my living room (this is where I had trouble getting to the back of the tv). The cable is a thick gauge and does an excellent job of drawing stable power to the stick. Once I plugged both sides in and pushed my TV back into position it was all set. You have to connect the cable to the firestick then the other end to your USB port. My TV is mounted in an awkward position so it was difficult to access the back of the tv. The only problem is you have to access the back of the TV for this cable to supply power to the firestick. You may have used powercfg.exe in low disk space situations to disable the hibernation file with. I've been using a firecable for a few months and it DOES work to power my firestick right off the TV usb port. It's a funny little tool that, on the one hand, lets you make minute tweaks to how power is used on your computer, but on the other hand, creates the most elaborate reports on how your PC uses power. During an outage, the UPS system keeps connected devices functioning by supplying electricity from its internal battery. My only suggestion to be really sure of not causing any problems is that if you wish to remove the Fire Stick from the TV is that you turn the power to the TV off before you remove the Fire Stick, rather than removing it from a powered TV. As long as electricity stays on, the UPS system provides utility power to the devices connected to its outlets, keeps its internal battery charged and protects equipment from power problems. Whereas, unless you have the power adapter connected to the wall outlet via a surge protector there is no protection whatsoever for the Fire Stick if a power surge occurs. In the event of a wall outlet power surge hopefully the TV will bear the brunt of it and the Fire Stick will be spared. If there is a situation where the current is less it could lead to possible 'data corruption' in the firmware of the Fire Stick if the power was fluctuating.īy using the TV's USB port, in effect the TV is acting as a power surge protector for the Fire Stick. As long as there is enough current being supplied by the USB port (see above proviso) it should be OK. In a way it may be a safer option than using the supplied power adapter. To be sure you would have to check the TV's specifications and see if you can find out what each USB port's maximum current output is.Īs to what damage may occur to the Fire Stick by powering this way. This is only conjecture on my part but the Fire Stick is drawing more current than the average USB device. Your TV's USB port seems to be supplying at least this amount of current as you say that there have been no issues.Īn issue may (I stress may only) arise if for example you have the Fire Stick being powered by the TV's USB port and you connect another USB device (if you have that many USB ports on your TV) and find that it doesn't work or that the Fire Stick then also doesn't work because the total power that is being supplied to the USB ports is not enough for both devices. It should be greater than 900mA (it probably is 1A). You may wish to check what is printed on the supplied power adapter that came with the Fire Stick as regards the output current to verify this. ) it seems that the Fire Stick requires >900mA to work effectively. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |